76 lines
2.3 KiB
C++
76 lines
2.3 KiB
C++
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
#include "../gcode.h"
|
|
#include "../../module/temperature.h"
|
|
#include "../../module/motion.h"
|
|
#include "../../module/planner.h"
|
|
#include "../../lcd/ultralcd.h"
|
|
|
|
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
|
|
#include "../../module/printcounter.h"
|
|
#endif
|
|
|
|
/**
|
|
* M104: Set hot end temperature
|
|
*/
|
|
void GcodeSuite::M104() {
|
|
if (get_target_extruder_from_command()) return;
|
|
if (DEBUGGING(DRYRUN)) return;
|
|
|
|
const uint8_t e = target_extruder;
|
|
|
|
#if ENABLED(SINGLENOZZLE)
|
|
if (e != active_extruder) return;
|
|
#endif
|
|
|
|
if (parser.seenval('S')) {
|
|
const int16_t temp = parser.value_celsius();
|
|
thermalManager.setTargetHotend(temp, e);
|
|
|
|
#if ENABLED(DUAL_X_CARRIAGE)
|
|
if (dual_x_carriage_mode == DXC_DUPLICATION_MODE && e == 0)
|
|
thermalManager.setTargetHotend(temp ? temp + duplicate_extruder_temp_offset : 0, 1);
|
|
#endif
|
|
|
|
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
|
|
/**
|
|
* Stop the timer at the end of print. Start is managed by 'heat and wait' M109.
|
|
* We use half EXTRUDE_MINTEMP here to allow nozzles to be put into hot
|
|
* standby mode, for instance in a dual extruder setup, without affecting
|
|
* the running print timer.
|
|
*/
|
|
if (parser.value_celsius() <= (EXTRUDE_MINTEMP) / 2) {
|
|
print_job_timer.stop();
|
|
LCD_MESSAGEPGM(WELCOME_MSG);
|
|
}
|
|
#endif
|
|
|
|
if (parser.value_celsius() > thermalManager.degHotend(e))
|
|
lcd_status_printf_P(0, PSTR("E%i %s"), e + 1, MSG_HEATING);
|
|
}
|
|
|
|
#if ENABLED(AUTOTEMP)
|
|
planner.autotemp_M104_M109();
|
|
#endif
|
|
}
|