359 lines
6.6 KiB
INI
359 lines
6.6 KiB
INI
# K1
|
|
# Printer_size: 220x220x250
|
|
# Version: v1.0.23
|
|
# CreateDate: 2023/03/21
|
|
# Nozzle_mcu: chip: GD32F303CBT6
|
|
# version: CR-K1-MAX-NOZZLE-V1.0.0
|
|
# Leveling_mcu: chip: GD32E230F8P6
|
|
# version: CR-K1-MAX-LEVELING-V1.0.0
|
|
# mcu: chip: GD32F303RET6
|
|
# version: CR4CU220812S12
|
|
|
|
[include sensorless.cfg]
|
|
[include gcode_macro.cfg]
|
|
[include printer_params.cfg]
|
|
|
|
[mcu]
|
|
serial: /dev/ttyS7
|
|
baud: 230400
|
|
restart_method: command
|
|
|
|
[mcu nozzle_mcu]
|
|
serial: /dev/ttyS1
|
|
baud: 230400
|
|
restart_method: command
|
|
|
|
[mcu leveling_mcu]
|
|
serial: /dev/ttyS9
|
|
baud: 230400
|
|
restart_method: command
|
|
|
|
[verify_heater extruder]
|
|
[verify_heater heater_bed]
|
|
check_gain_time: 120
|
|
heating_gain: 1.0
|
|
hysteresis: 10
|
|
|
|
[mcu rpi]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[bl24c16f]
|
|
i2c_mcu: rpi
|
|
i2c_bus: i2c.2
|
|
i2c_speed: 400000
|
|
|
|
[idle_timeout]
|
|
timeout: 99999999
|
|
|
|
[virtual_sdcard]
|
|
path: /usr/data/printer_data/gcodes
|
|
|
|
[gcode_arcs]
|
|
resolution: 1.0
|
|
|
|
[temperature_sensor mcu_temp]
|
|
sensor_type: temperature_mcu
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
[temperature_sensor chamber_temp]
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC5
|
|
min_temp: 0
|
|
max_temp: 125
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: !PB9
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 72
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_endstop: 229
|
|
position_min: -5
|
|
position_max: 229
|
|
homing_speed: 36
|
|
homing_retract_dist:0
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin:PA9
|
|
interpolate: True
|
|
run_current:1.5
|
|
hold_current:1.0
|
|
sense_resistor: 0.100
|
|
stealthchop_threshold: 0
|
|
uart_address:3
|
|
diag_pin: ^PB12
|
|
# driver_IHOLDDELAY: 8
|
|
# driver_TPOWERDOWN: 20
|
|
# driver_TBL: 1
|
|
# driver_TOFF: 1
|
|
# driver_HEND: 0
|
|
# driver_HSTRT: 7
|
|
driver_SGTHRS: 65
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: !PB7
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 72
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_endstop: -0.5
|
|
position_min: -0.5
|
|
position_max: 226
|
|
homing_speed: 36
|
|
homing_retract_dist:0
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin:PA10
|
|
interpolate: True
|
|
run_current:1.5
|
|
hold_current:1.0
|
|
sense_resistor: 0.100
|
|
stealthchop_threshold: 0
|
|
uart_address:3
|
|
diag_pin: ^PB13
|
|
# driver_IHOLDDELAY: 8
|
|
# driver_TPOWERDOWN: 20
|
|
# driver_TBL: 1
|
|
# driver_TOFF: 1
|
|
# driver_HEND: 0
|
|
# driver_HSTRT: 7
|
|
driver_SGTHRS: 65
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: !PB5
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance:8
|
|
gear_ratio: 64:20
|
|
endstop_pin: tmc2209_stepper_z:virtual_endstop# PA15 #probe:z_virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 255
|
|
position_min: -5
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PA11
|
|
uart_address: 3
|
|
run_current: 0.8
|
|
diag_pin: ^PB14
|
|
stealthchop_threshold: 0
|
|
sense_resistor: 0.100
|
|
# driver_IHOLDDELAY: 8
|
|
# driver_TPOWERDOWN: 20
|
|
# driver_TBL: 1
|
|
# driver_TOFF: 1
|
|
# driver_HEND: 2
|
|
# driver_HSTRT: 2
|
|
driver_SGTHRS: 0
|
|
|
|
[extruder]
|
|
max_extrude_only_distance: 1000.0
|
|
max_extrude_cross_section: 80
|
|
step_pin: nozzle_mcu:PB1
|
|
dir_pin: nozzle_mcu:PB0
|
|
enable_pin: !nozzle_mcu:PB2
|
|
microsteps: 16
|
|
rotation_distance: 6.9
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: nozzle_mcu:PB7
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: nozzle_mcu:PA0
|
|
pressure_advance: 0.04
|
|
pressure_advance_smooth_time: 0.040
|
|
control: pid
|
|
pid_Kp: 25.013
|
|
pid_Ki: 2.566
|
|
pid_Kd: 60.966
|
|
min_temp: 0
|
|
max_temp: 320
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: nozzle_mcu:PB11
|
|
tx_pin: nozzle_mcu:PB10
|
|
uart_address: 3
|
|
run_current: 0.55
|
|
sense_resistor: 0.150
|
|
stealthchop_threshold: 0
|
|
# driver_IHOLDDELAY: 8
|
|
# driver_TPOWERDOWN: 20
|
|
# driver_TBL: 2
|
|
# driver_TOFF: 3
|
|
# driver_HEND: 0
|
|
# driver_HSTRT: 5
|
|
|
|
[heater_bed]
|
|
heater_pin: PB10
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC4
|
|
control: watermark
|
|
# control: pid
|
|
# pid_kp: 27
|
|
# pid_ki: 0.08
|
|
# pid_kd: 0
|
|
min_temp: 0
|
|
max_temp: 120
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
pause_on_runout: true
|
|
switch_pin: !PC15
|
|
runout_gcode:
|
|
{% if printer.extruder.can_extrude|lower == 'true' %}
|
|
G91
|
|
G0 E30 F600
|
|
G90
|
|
{% endif %}
|
|
|
|
[filament_switch_sensor filament_sensor_2]
|
|
pause_on_runout: true
|
|
switch_pin: !nozzle_mcu:PA10
|
|
|
|
[multi_pin heater_fans]
|
|
pins:nozzle_mcu:PB5,PB2
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: multi_pin:heater_fans
|
|
heater: extruder
|
|
heater_temp: 40
|
|
|
|
[static_digital_output my_fan_output_pins]
|
|
pins: nozzle_mcu: PB6
|
|
|
|
[output_pin fan0]
|
|
pin: !nozzle_mcu: PB8
|
|
pwm: True
|
|
cycle_time: 0.0100
|
|
hardware_pwm: false
|
|
value: 0.00
|
|
scale: 255
|
|
shutdown_value: 0.0
|
|
|
|
[output_pin fan1]
|
|
pin: PC0
|
|
pwm: True
|
|
cycle_time: 0.0100
|
|
hardware_pwm: false
|
|
value: 0.00
|
|
scale: 255
|
|
shutdown_value: 0.0
|
|
|
|
[output_pin fan2]
|
|
pin: PB1
|
|
pwm: True
|
|
cycle_time: 0.0100
|
|
hardware_pwm: false
|
|
value: 0.00
|
|
scale: 255
|
|
shutdown_value: 0.0
|
|
|
|
[output_pin LED]
|
|
pin:PB0
|
|
pwm: True
|
|
cycle_time: 0.010
|
|
value: 1
|
|
|
|
[adxl345]
|
|
cs_pin: nozzle_mcu:PA4
|
|
spi_speed: 5000000
|
|
axes_map: x,-z,y
|
|
spi_software_sclk_pin: nozzle_mcu:PA5
|
|
spi_software_mosi_pin: nozzle_mcu:PA7
|
|
spi_software_miso_pin: nozzle_mcu:PA6
|
|
|
|
[resonance_tester]
|
|
accel_chip: adxl345
|
|
accel_per_hz: 75
|
|
# min_freq: 30
|
|
# max_freq: 100
|
|
probe_points:
|
|
110,110,10
|
|
|
|
[prtouch_v2] # K1
|
|
pr_version: 1
|
|
step_base: 2
|
|
z_offset: 0
|
|
noz_ex_com: 0.05
|
|
tilt_corr_dis: 0.03
|
|
tri_min_hold: 2000
|
|
tri_max_hold: 6000
|
|
pres_cnt: 4
|
|
pres0_clk_pins: leveling_mcu:PA5
|
|
pres0_sdo_pins: leveling_mcu:PA1
|
|
pres1_clk_pins: leveling_mcu:PA2
|
|
pres1_sdo_pins: leveling_mcu:PA0
|
|
pres2_clk_pins: leveling_mcu:PA6
|
|
pres2_sdo_pins: leveling_mcu:PA3
|
|
pres3_clk_pins: leveling_mcu:PA7
|
|
pres3_sdo_pins: leveling_mcu:PA4
|
|
show_msg: False
|
|
step_swap_pin: PC10
|
|
pres_swap_pin: leveling_mcu:PB1
|
|
g28_wait_cool_down: true
|
|
pa_clr_down_mm: -0.15
|
|
clr_noz_start_x: 95
|
|
clr_noz_start_y: 221
|
|
clr_noz_len_x: 40
|
|
clr_noz_len_y: 2
|
|
speeds: 2.5,1.0
|
|
tri_hftr_cut: 2,1
|
|
tri_lftr_k1: 0.70,0.30
|
|
tri_try_max_times: 10
|
|
tri_min_hold: 2000,20000
|
|
tri_max_hold: 6000,60000
|
|
|
|
[bed_mesh]
|
|
speed: 150
|
|
mesh_min: 5,5
|
|
mesh_max: 215,215
|
|
probe_count: 5,5
|
|
fade_start: 5.0
|
|
fade_end: 50.0
|
|
|
|
[display_status]
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 800
|
|
max_accel: 20000
|
|
max_accel_to_decel: 20000
|
|
max_z_velocity: 20
|
|
square_corner_velocity: 5.0
|
|
square_corner_max_velocity: 200.0
|
|
max_z_accel: 300
|
|
|
|
[pause_resume]
|
|
# recover_velocity: 500.
|
|
|
|
[exclude_object]
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [input_shaper]
|
|
#*# shaper_type_y = ei
|
|
#*# shaper_freq_y = 70.6
|
|
#*# shaper_type_x = ei
|
|
#*# shaper_freq_x = 70.6
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.750375, 0.683438, 0.618375, 0.554406, 0.549500
|
|
#*# 0.494406, 0.396906, 0.336531, 0.254031, 0.208813
|
|
#*# 0.241094, 0.138281, 0.050000, -0.016094, -0.067906
|
|
#*# 0.047000, -0.061844, -0.160844, -0.261625, -0.368750
|
|
#*# -0.049375, -0.189781, -0.326906, -0.456375, -0.529906
|
|
#*# x_count = 5
|
|
#*# y_count = 5
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = lagrange
|
|
#*# tension = 0.2
|
|
#*# min_x = 5.0
|
|
#*# max_x = 215.0
|
|
#*# min_y = 5.0
|
|
#*# max_y = 215.0
|